Nuovo biomateriale in idrogel e fibra di vetro


Efforts are currently underway around the world to create materials that are friendly to both society and the environment. Among them are those that comprise different materials, which exhibit the merits of each component.
Hokkaido University researchers, led by Professor Jian Ping Gong, have focused on creating a reinforced material using hydrogels. Though such a substance has potential as a structural biomaterial, up until now, no material reliable and strong enough for long-term use has been produced. This study was conducted as a part of the Cabinet Office’s Impulsing Paradigm Change through Disruptive Technologies Program (ImPACT).
To address the problem, the team combined hydrogels containing high levels of water with glass fiber fabric to create bendable, yet tough materials, employing the same method used to produce reinforced plastics. The team found that a combination of polyampholyte (PA) gels, a type of hydrogel they developed earlier, and glass fiber fabric with a single fiber measuring around 10μm in diameter produced a strong, tensile material. The procedure to make the material is simply to immerse the fabric in PA precursor solutions for polymerization.
When used alone, the fiber-reinforced hydrogels developed by the team are 25 times tougher than glass fiber fabric, and 100 times tougher than hydrogels – in terms of the energy required to destroy them. Combining these materials enables a synergistic toughening. The team theorizes that toughness is increased by dynamic ionic bonds between the fiber and hydrogels, and within the hydrogels, as the fiber’s toughness increases in relation to that of the hydrogels. Consequently, the newly developed hydrogels are 5 times tougher compared to carbon steel.
“The fiber-reinforced hydrogels, with a 40 percent water level, are environmentally friendly,” says Dr. Jian Ping Gong, “The material has multiple potential applications because of its reliability, durability and flexibility. For example, in addition to fashion and manufacturing uses, it could be used as artificial ligaments and tendons, which are subject to strong load-bearing tensions.” The same principles can also be applied to other soft components, such as rubber.

Read more at: https://phys.org/news/2017-02-tough-composites-hydrogels-woven-fiber.html#jCp

Photo caption: The newly developed fiber-reinforced hydrogel consists of polyampholyte (PA) gels and glass fiber fabric. The team theorizes that toughness is increased by dynamic ionic bonds between the fiber and hydrogels, and within the hydrogels. Credit: Hokkaido University


Leggi anche

Il peso dei satelliti spaziali può rendere costoso il raggiungimento dell’orbita terrestre bassa (LEO). Se ne sono rese conto le aziende australiane che hanno dovuto fare i conti con i fornitori di lancio che fatturano i carichi utili al chilogrammo. È emersa quindi la necessità di utilizzare strutture più leggere, ma al tempo stesso robuste, per resistere in ambienti spaziali con temperature estreme….

Leggi tutto…

The structural acrylic adhesives ARALDITE®2080 and ARALDITE®2081 from Huntsman have been developed to ensure high strength and lower flammability than traditional methyl methacrylate-based products. For most applications, they require minimal surface preparation and ensure good adhesion performance on different substrates (plastic, composites and metal) along with rapid curing at room temperature….

Leggi tutto…

Un gruppo di ricercatori dell’Università del Queensland del Sud, sotto la guida del dottor Wahid Ferdous, sta studiando come sostituire le traverse ferroviarie in legno per i ponti con un nuovo materiale costituito da fibre composite e materiali di scarto. Il governo dello stato del Queensland e il produttore di traverse in cemento Austrak hanno finanziato il progetto attraverso una borsa di ricerca per l’industria….

Leggi tutto…

Analizzando le proprietà dei nuovi ritardanti di fiamma per materiali compositi, i ricercatori del laboratorio Advanced Fibers dell’Empa, centro svizzero per lo studio dei materiali avanzati, sotto la guida di Sabyasachi Gaan, hanno elaborato una tecnica che permette di rendere recuperabili le resine epossidiche, il cui limite di riutilizzo è intrinseco alla natura di materiali termoindurenti, ossia polimeri altamente reticolati che, una volta induriti, non possono essere sottoposti nuovamente a fusione senza carbonizzarsi….

Leggi tutto…

Refitech Composite Solutions innova i propri processi produttivi, installando una macchina CNC a cinque assi per la finitura di componenti compositi, che si aggiunge ai sistemi già operativi a tre assi. La nuova strumentazione consentirà di eseguire la lavorazione di forme 3D ancora più complesse in modo completamente automatico, ad alta velocità, garantendo una qualità elevata e una riproducibilità perfetta, in vista dei volumi di serie….

Leggi tutto…